User Guide uPrint SE and uPrint SE Plus - English

Creada por Francisco Briones, Modificado el Lun., 4 Abr., 2022 a las 11:22 A. M. por Francisco Briones

Download the PDF guide at the end of this article, in it you could find the following:


TABLE OF CONTENTS 

 

1.- INTRODUCTION 

  • HOW TO USE THIS GUIDE
  • LEARN MORE
  • SAFETY PRECAUTIONS 

2.- OVERVIEW 

  • FINDING MORE INFORMATION 

3.- SETUP 

  • INSTALLING SOFTWARE 

Installing CatalystEX

Installing system software to the workstation 

  • NETWORKING THE PRINTER

Connecting through a network

Connecting directly to a workstation

  • ESTABLISHING NETWORK COMMUNICATION WITH THE PRINTER 

Establishing communication on a dynamic network 

Establishing communication on a static network 

  • INSTALLING SYSTEM SOFTWARE ON PRINTER 
  • ADDING THE SECOND MATERIAL BAY

Installing the Material Bay

4.- OPERATION 

  • DISPLAY PANEL AND KEYPAD 
  • SYSTEM SOFTWARE OVERVIEW
  • CATALYSTEX OVERVIEW
  • PROCESSING YOUR STL FILE FOR PRINTING

Opening your STL file with CatalystEX

Selecting layer resolution 

Selecting model interior fill style 

Selecting support style 

Selecting the scale of your STL file 

Selecting the orientation of your STL file

Adding your STL file to the pack

Printing your STL file 

  • BUILDING A PART 

Starting a build from a remote location

Starting a build from the display panel 

  • THE DISPLAY PANEL DURING BUILD 
  • CHAMBER LIGHTS 
  • PAUSING A BUILD 
  • RESUMING AFTER PAUSE
  • CANCELING A BUILD 
  • REMOVING A COMPLETED PART 

Remove a part from the modeling base 

  • REMOVING SUPPORT MATERIAL 

Emptying the purge bucket

  • REPLACING MATERIAL FOR SINGLE MATERIAL BAY
  • REPLACING MATERIAL FOR DUAL MATERIAL BAYS
  • MATERIAL BAY LEDS
  • REPLACING MATERIAL SPOOLS

Removing a spool of material from the carrier

  • STORING MATERIAL SPOOLS 
  • AUTO POWER DOWN 

Canceling auto power down 

  • POWERING OFF 
  • RESUMING OPERATIONS FROM STANDBY MODE
  • UPDATING PRINTER SYSTEM SOFTWARE

Installing the system software 

5.- MAINTENANCE 

  • STARTUP KIT TOOLS
  • PREVENTIVE MAINTENANCE 

Daily

  • 500 HOUR MAINTENANCE

Tip wipe assembly 

Tip shield replacement 

Remove debris from the Filament Present switch 

  • 2000 HOUR MAINTENANCE

Tip replacement and calibration 

Chamber light bar replacement 

6.- TROUBLESHOOTING 

  • TROUBLESHOOTING 
  • FAULT DETERMINATION CODES 
  • EXPORTING PRINTER CONFIGURATION (.CFG) FILE

Exporting configuration file from printer

  • CYCLING POWER
  • DIAGNOSING LOSS OF EXTRUSION
  • CLOGGED TIP

Material Jam 

  • RECOVERING FROM LOSS OF EXTRUSION

7.- SUPPORT 

  • REGISTRATION 
  • CUSTOMER SUPPORT 

8.- RECYCLING 

  • RECYCLING CODES
  • REMOVING THE EEPROMS FROM THE MATERIAL GUIDES
  • REMOVING THE DESICCANT FROM THE MATERIAL SPOOL

9.- PRINTER SPECIFICATIONS 

  • PHYSICAL SPECIFICATIONS
  • FACILITY SPECIFICATIONS
  • WORKSTATION SPECIFICATIONS
  • POWER SPECIFICATIONS
  • ENVIRONMENTAL SPECIFICATIONS 
  • ACOUSTIC SPECIFICATIONS
  • 10 SUPPLEMENTAL INFORMATION 
  • UNINTERRUPTIBLE POWER SUPPLY

Use and Installation 

General Information

Parts List – Cable, UPS to 3D Printer

  • DECLARATION OF CONFORMITY
  • REGULATORY AND ENVIRONMENTAL INFORMATION

EMC Class A Warning

FCC Statements (U.S.A.) 

Canada Electromagnetic compatibility (EMC) 

MSDS (Material Safety Data Sheet)

Disposal of waste equipment by users in private households in the European Union 

¿Le fue útil este artículo?

¡Qué bueno!

Gracias por sus comentarios

¡Sentimos mucho no haber sido de ayuda!

Gracias por sus comentarios

¡Díganos cómo podemos mejorar este artículo!

Seleccione al menos una de las razones
La verificación de CAPTCHA es obligatoria.

Comentarios enviados

Agradecemos su iniciativa, e intentaremos corregir el artículo