F120 User Guide - English

Creada por Francisco Briones, Modificado el Fri, 25 Mar 2022 a las 10:29 AM por Francisco Briones

In the attached file you can find the following topics related to the F120 3D printer


1.- SERVICE AND SUPPORT

  • Hazard Types
  • Product Safety Signs
  • Product Safety Label Locations
  • Potential Safety Hazard Areas
  • Door Locks 
  • General Safety Practices
  • Environmental Requirements

2.- PRINTER SETUP

  • Welcome Kit Contents
  • Identifying Your Printer
  • Making the Network Connection
  • Connecting the Power Cable
  • Configuring the Network
  • Installing GrabCAD Print
  • Connecting to the F120 Printer
  • Setting the Printer’s Date and Time
  • Updating the Controller software Version
  • Adjusting the Tip Wipe Height

3.- SYSTEM COMPONENTS

  • Access Doors and Panels
  • Interface Panel
  • Oven Door
  • Oven Light
  • Platen
  • Tip Wipe Assemblies
  • Purge Chute
  • Material Coil Box
  • Print Heads
  • Materials Used
  • Material Coil Box Memory Chip
  • Tips and Slice Height
  • Controller Software
  • GrabCAD Print Software

4.- USER INTERFACE

  • Navigation Menu
  • Display Area
  • Loading a File
  • Viewing Print Job Information
  • Build Status Display
  • Print Job Controls
  • Adding a Job to the Job Queue
  • Editing the Job Queue
  • Viewing Job Details
  • About the Sample Queue
  • Head Status Icons
  • Viewing Head Details
  • Material Status Icons
  • Viewing Material Details
  • Material Load Controls
  • Tools Page Menu
  • Navigation Overview
  • Settings
  • Calibration
  • Maintenance
  • Network
  • Power
  • Light 

5.- OPERATING THE PRINTER

  • Powering ON the Printer
  • Powering OFF the Printer
  • Material Coil Box Preparation
  • Connecting Material Coil Box To Printer
  • Handling/Storing Materials
  • Replacing a Head
  • Before a Build
  • Preparing the Printer
  • Selecting a Job to Build
  • Information Available During a Build
  • Build Warnings
  • Pausing a Build
  • Aborting a Build
  • After a Build is Complete
  • Job Storage
  • Part Build Location
  • Display Units
  • Oven Temperature Control
  • Touchscreen Display Brightness
  • Display Language
  • Head Odometer Status
  • Materials Status
  • Temperature Status
  • Software Version
  • MTConnect System Activation

6.- CALIBRATION AND ADJUSTMENTS

  • Automatic Tip Calibration
  • Manual Tip Calibration

7.- MAINTENANCE

  • USB Flash Drive Method
  • GrabCAD Print Method
  • USB Flash Drive Method
  • GrabCAD Print Method
  • Cleaning the Oven Chamber
  • Cleaning the Platen
  • Clean/Inspect Tip Wipe Assemblies
  • Cleaning the Exterior Surface of the Printer
  • Cleaning the Touchscreen Display
  • Inspecting and cleaning the tip shields
  • Cleaning the Oven Door glass Surfaces
  • Powering Off
  • Rear Panel
  • Right and Left Side Panels
  • Right and Left Side Louver Panels
  • Top Cover Assembly
  • 3.3/5/12 VDC ATX Power Supply
  • Oven Thermistor
  • Replacing a Head
  • Head Ribbon Cables
  • Touchscreen Display
  • Right and Left Side Oven Blowers
  • Oven Door Gasket
  • Z Drive Belt
  • Y Bellows
  • Oven Light
  • Oven Door CameraOven Door Latch
  • Top Cover Interlock Sensor and Actuator

8.- TROUBLESHOOTING

  • Warnings at Build Start
  • Errors Preventing a Build from Starting
  • Load/Unload Errors
  • Build Pause Warnings
  • Build Abort Errors
  • Head Warnings
  • Head Errors

9.- SUPPLEMENTARY INFO

  • EMC Class A Warning
  • FCC Statements (U.S.A.)
  • Canada Electromagnetic compatibility (EMC)
  • MSDS (Material Safety Data Sheet)
  • Disposal of Waste Equipment by Users in Private Households in the European Union

¿Le fue útil este artículo?

¡Qué bueno!

Gracias por sus comentarios

¡Sentimos mucho no haber sido de ayuda!

Gracias por sus comentarios

¡Díganos cómo podemos mejorar este artículo!

Seleccione al menos una de las razones
La verificación de CAPTCHA es obligatoria.

Comentarios enviados

Agradecemos su iniciativa, e intentaremos corregir el artículo